Previous Next
  1. Home
  2. Get Creative
  3. Quilting
  4. Wall Hanging

Sewing Project - Wall Hanging


The mix of classic techniques and modern expressions will make sure that this wall hanging adorns any wall in your home.

Wall Hanging

Sewing project - Wall Hanging


Create a completely individual Wall Hanging using the PFAFF creative™ 3.0 sewing and embroidery machine and PFAFF Stitch Creator™.


To create a unique wall hanging you will need:


  •          PFAFF® creative 3.0 sewing and embroidery machine
  •          Free-motion Echo quilting foot #821002096
  •          ¼” Right guide foot for IDT™ System #820924096
  •          Piping foot #820532096
  •          INSPIRA® Fast & Easy Tear-A-Way Light 16”x10 yards (#620113396) or 12”x10 yards                          (#620113296)
  •          Quilter’s cotton – solid or tone on tone prints in the following colors:
             Off-white 31”x 28” (79x71cm)
             Blue 7½” x15” (19x38cm)
             Dark teal 24”x 8” (60x20)
             Light teal 7½” x15” (19x38cm)
  •          Cotton batting 39”x 29” (100x75cm)
  •          Cotton backing 39”x 29” (100x75cm)
  •          Cord for piping 2.9 yards (2.70m)
  •          Fabric for piping cut on the bias
  •          Embroidery thread 40wt rayon
  •          Embroidery thread 30wt cotton
  •          Sewing thread
  •          Satin ribbon, ⅛” (3mm) wide in two colors

Finished size approximately 42”x26 ½” (107 x 67cm)


Shape Creator™ Feature
The embroideries on the squares were created using the Shape Creator™ feature. Play with the feature yourself to create a design or use the downloadable file, Quilt_square. Embroider on teal fabric and trim squares to 7¼” x 7¼” (18x18cm).

Piece the upper section according to the diagram using ¼” seam allowance. Create diagonal rows by adding triangles on either side of the squares, and then sew the rows together.

Ribbon stitches
Choose one of the new ribbon stitches and sew it about 1” (2.5cm) from the top edge of the 31”x 28” (79x71cm) off-white cotton fabric. We used stitch 6.6.7 and sewed it with two different colors of ⅛” satin ribbon on a single layer of fabric with tear-a-way stabilizer behind it. See detailed instructions for double ribbon stitches in your owner’s manual.

Attach the pieced top to the lower section.

Place cotton batting behind the whole lower section before you continue.
Thread with 30 wt. cotton thread.

Quilt Embroidery
Download embroidery Quilt_leaves, an endless leaf design; transfer it to your machine. Embroider the design four times. Position the embroidery below the ribbon stitches, approximately 5½” (14cm) from the top edge

The embroidery featured at the bottom of the wall hanging is from PFAFF® collection 408 Feather Quilting. Download design Quilt_swirl and transfer it to your machine.

Embroider the design four times along the bottom edge – opposite the ribbon stitches. Use the illustration as a guide for placement.

Free-motion stitching is added to accent the embroidery and create additional texture on the project.

Fill in the flowers from the endless embroidery with free-motion stitching. See example in illustration.
Echo quilt around the border embroidery as desired, using the Free-motion Echo quilting foot. We stitched four rows approximately ⅜” (1cm) apart.

In the space between the embroidered areas, draw lines to define two areas for free-motion stitching. Refer to the illustration for placement and suggestions for type of stitching. Fill in these areas with your favorite free-motion technique.

In the top section of the wall hanging, fill in the triangles with free-motion sewing.

Stitch Creator™ Feature
Use the Stitch Creator™ Feature to create the decorative stitches that outline the free-motion areas. See attached step-by-step document. (Exercise from creative vision as a downloadable file) Sew along the edge of the free-motion as shown.

Trim the quilt to approximately 43”x27½” (110x70cm)

Add tabs along the top edge to hang your quilt. Cut 5 pieces approximately 8 ½” long x 4” wide (22cm long x 10cm wide). Sew into tubes then fold into loops. Evenly space the loops along the top of the hall hanging.

Create your own piping using one of the fabrics from your wall hanging. See detailed instructions in the online Accessory Catalog.

Sew the piping around the wall hanging using the Piping Foot.

Place backing fabric right sides together with the wall hanging and sew again in the same stitching line as for the piping. Leave an opening on one side to turn project right side out.


Download Wallhanging Embroideries

Stitch Creator™ Feature, Step-by-Step



You might also like:

  • Free-Motion Echo Quilting Foot
  • 1/4 inch Right Guide Foot for IDT™ System
  • Piping Foot
  • INSPIRA® Fast & Easy Tear-A-Way Light